Тема: Kaeser DSD 141 (belt drive)

[i_borisov]

Hello,
We have one old compressor Kaeser DSD 141 (yom 2003) that is with belts. We need to change the working pressure of the compressor from 8 Bar to 10 Bar. Since this is not the new direct driver version we need to change the transition ratio. Do you know what is the rotation speed of the airend of the belt driven Kaeser DSD 141 with 10 bar pressure.

Thank you

[Timich.S]

Хм, опять Инглиш.
你好。

[Evgenii0455]

Хм, опять Инглиш.
你好。

как понял он хочет 8 барный в 10 переделать

[Evgenii0455]

Hello,
We have one old compressor Kaeser DSD 141 (yom 2003) that is with belts. We need to change the working pressure of the compressor from 8 Bar to 10 Bar. Since this is not the new direct driver version we need to change the transition ratio. Do you know what is the rotation speed of the airend of the belt driven Kaeser DSD 141 with 10 bar pressure.

Thank you

Hello, I understand you want to increase the maximum pressure by changing the transmission ratio of the belt drive?

[i_borisov]

Hello,
We have one old compressor Kaeser DSD 141 (yom 2003) that is with belts. We need to change the working pressure of the compressor from 8 Bar to 10 Bar. Since this is not the new direct driver version we need to change the transition ratio. Do you know what is the rotation speed of the airend of the belt driven Kaeser DSD 141 with 10 bar pressure.

Thank you

Hello, I understand you want to increase the maximum pressure by changing the transmission ratio of the belt drive?

Exactly! Now I need to know the airend speed of compressor Kaeser DS141 at 10 bar in order to make the correct ratio.

[Evgenii0455]

Hello,
We have one old compressor Kaeser DSD 141 (yom 2003) that is with belts. We need to change the working pressure of the compressor from 8 Bar to 10 Bar. Since this is not the new direct driver version we need to change the transition ratio. Do you know what is the rotation speed of the airend of the belt driven Kaeser DSD 141 with 10 bar pressure.

Thank you

Hello, I understand you want to increase the maximum pressure by changing the transmission ratio of the belt drive?

Exactly! Now I need to know the airend speed of compressor Kaeser DS141 at 10 bar in order to make the correct ratio.

To begin with, it is necessary to make a belt drive calculation to determine the number of revolutions on the pulley of the screw pair (or to measure with a special device) and the gear ratio of this gear, then information on the screw turns is required at 10 bar compressor version. then pick the pulleys based on the calculation of the new gear.
information on the 10 bar transmission can be found if anyone has a similar compressor in the performance of 10 bar, and in general Kaiser in Russia is a separate conversation)

[i_borisov]

information on the 10 bar transmission can be found if anyone has a similar compressor in the performance of 10 bar, and in general Kaiser in Russia is a separate conversation)

That is why I am posting this question if someone has a Kaeser compressor DS141 10bar or if someone has information about the airend rotation speed.
Kaeser would not give this information.

[Android13]

My compliments. Please write the engine speed, the diameters of the pulleys.
And the performance of the compressor at 8 bar.

[Evgenii0455]

My compliments. Please write the engine speed, the diameters of the pulleys.
And the performance of the compressor at 8 bar.

Тоже ньюанс) производительность по умолчанию не интересует как понимаю

[Sure_man]

Хеллоу!
смотри тех характеристики во вложении
там есть обороты ведущего винта винтового блока...