Страница 1 из 2

Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 08 янв 2015, 14:35
i_borisov
Hallo.
We have compressor Atlas Copco GA22 with controller Elektronikon I. On power up there is a message "System Failure 200" and compressor does not start. What does System Failure 200 means?

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 08 янв 2015, 15:52
Технолог
i_borisov писал(а):Hallo.
We have compressor Atlas Copco GA22 with controller Elektronikon I. On power up there is a message "System Failure 200" and compressor does not start. What does System Failure 200 means?

Hi! The serious error, I think. In this thread viewtopic.php?f=8&t=692 users discussed error 202, and little bit about 200 (maybe you should to check fuses?). Unfortunately, so little information, but you try email to user, who left his contact. Thread on Russian, because the forum on Russian too )

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 08 янв 2015, 20:20
Batalt
i_borisov писал(а):Hallo.
We have compressor Atlas Copco GA22 with controller Elektronikon I. On power up there is a message "System Failure 200" and compressor does not start. What does System Failure 200 means?

Hi! What part number in the controller or its generation (Мк3?) ?

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 08 янв 2015, 23:05
ws2000
Технолог писал(а):
i_borisov писал(а):Hallo.
We have compressor Atlas Copco GA22 with controller Elektronikon I. On power up there is a message "System Failure 200" and compressor does not start. What does System Failure 200 means?

Hi! The serious error, I think. In this thread viewtopic.php?f=8&t=692 users discussed error 202, and little bit about 200 (maybe you should to check fuses?). Unfortunately, so little information, but you try email to user, who left his contact. Thread on Russian, because the forum on Russian too )

я так понимаю, это про меня.. :)
вариантов по той проблеме (202) было несколько... в том числе и умирающая батарея памяти (+3V), и кольцевые трещины, и падение напряжения одной фазы (плохой контакт в том числе), и дикое (!) количество пусков двигателя.
голова кругом шла... клиент попался дерьмовый: всё они (гл. энергетик) знают и умеют лучше сервиса атлас копко...
ща пороюсь, завтра отпишусь чё тогда было, + посмотрю по ошибке 200.
P.S. .. а ремонты бываю и такие:

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 09 янв 2015, 12:18
i_borisov
Thank you all for your answers.

You can see below a picture of the controller. Thank you ws2000 for your answer. Our controller is diferent from the one on your picture. Do you know how to check if this is a battery problem for controller Elektronikon I?
I dont think that the problem is with bad phase connections or broken tracks or engine starts.
Another strange thing is that the working hours on the controller are reset to 0 (both loaded and offload).
Thank you

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 09 янв 2015, 13:51
ws2000
прям де жа вю !!! именно такой и был с 202 ошибкой... короче, атлас копко с такой ошибкой рекомендовал замену панели.
учитывая, что у вас счётчики наработки скидываються на "0" - батарейке памяти "хана"... проверить можно: надо снять заднюю крышку электроникона (на моём она выглядит так:) и померить тестером. удачи.

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 09 янв 2015, 14:06
ws2000
батарея памяти самая обычная, на радиорынке можно найти
P.S. the device is old already.. and the capacitors could dry up and the battery to sit down.. it is better to replace it with a new panel, the estimated cost of the issue (in our swamp) 1000 Euro with programming.

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 09 янв 2015, 20:59
Batalt
All right. For Mk 3 recommended the following сounter measure:

1. Check for part number. If below 1900 0700 05, replace
with new version.
2. Switch off/on the voltage, sometimes the failure is recoverable! If still
no operation? Continue checklist.
3. Check Operating voltage. Too high/low supply voltage (2X1-1 and –2).
Operating voltage must be between 16 and 34Vac.
Check for strong voltage fluctuations. How stable/unstable is the mains
supply? Consult customer.
4. When time & date indicate non-relevant values, the clock IC is damaged.
Replace module.
5. If System Failure 200 persists, probably there’s damaged component.
Replace module.

I agree with ws2000. I think most logical to do retrofit on Mk5.

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 29 май 2015, 20:57
aleksandr5796
IMG_20150529_184004.jpg
Два раза фотографировал и каждый раз цифра 200 мигала...
IMG_20150529_184004.jpg (28.73 KiB) Просмотров: 9867
ws2000 писал(а):батарея памяти самая обычная, на радиорынке можно найти
P.S. the device is old already.. and the capacitors could dry up and the battery to sit down.. it is better to replace it with a new panel, the estimated cost of the issue (in our swamp) 1000 Euro with programming.

Уважаемый ws2000! У меня такая же проблема, и контроллер выглядит так же как у коллеги из Болгарии. Вот только батарейки внутри я не нашёл (ни батареи ни гнезда под неё)...Разобрал там две платы и усё...К слову сказать компрессор несколько лет не эксплуатировался, сейчас решили проверить, при подаче напряжения выдаёт "System Failure 200" и ни какой реакции на кнопку "пуск"
Подскажите где может быть батарея?
Р.S. Дата сбивается после отключения, ну и предохранители снял, а там "жуки"....

Re: Atlas Copco Elektronikon System Failure 200

СообщениеДобавлено: 29 май 2015, 21:51
i_borisov
Hello aleksandr5796,

With the kind help of user ws2000 I understood that System Failure 200 means that there is problem with the EPROM memory. In my case it was a dead battery. The battery for this controller is inside the TIMEKEEPER RAM and unfortunatelly it cannot be changed. The solution is to change the TIMEKEEPER RAM, but in this case you have to upload the data to thetimekeer. I found on the internet some folks, who cut the timekeeper and put a new battery, but I was not able to do this:
http://www.automatenfreunde.de/download/tk/05-anschluss.jpg
If you want to take the hard way and change the timekeeper you can buy this model on ebay (from China)

In my case I changed the controller.